Skip to content
Eggshell & Co Painting 09 870 5756

How many coats of paint

Two finish coats is the standard on almost every surface, inside and out. New or bare timber gets a primer first, and a big colour change can need a third coat. BRANZ advises two topcoats on weatherboards. The second coat is not a luxury: it closes the thin spots the first leaves at edges and corners. Preparation explains what comes before the coats.

Paint tin, tray and brushes laid out on newspaper on a timber floor
Interior painting gear set out on a protected floor. Photo: David Mulder, CC BY-SA 2.0

Why two finish coats

Paint goes on thinner than it looks, and thinnest at edges, corners and the bottom edges of weatherboards, exactly where weather attacks first. A second coat builds the film to the thickness the paint maker designed for, closes pinholes and gives even colour. One-coat jobs look fine at first and wear through sooner.

Resene’s durability figures for acrylic on weatherboards assume a full three-coat system: primer or spot-primer plus two finish coats. A quote with one finish coat should cost less, and the paint will not last as long.

Typical coat counts by job

Most jobs follow a simple pattern: prime or seal whatever is bare, then two finish coats over everything. New timber and big colour changes add a coat; sound paint in the same colour needs only spot-priming. Your painter should still follow the paint maker’s system for the products used, which may add an undercoat or a sealer.

Typical coat counts. Follow the maker’s specified system.
Job Typical coats
Exterior repaint over sound paint, same colour Spot-prime bare areas, two finish coats
Bare or new exterior timber Primer, two finish coats (some systems add an undercoat)
Big colour change, dark to light Primer-undercoat or extra coat, two finish coats
Interior walls, same colour Spot-seal patches, two finish coats
New plasterboard Sealer, two finish coats
Ceilings Two ceiling coats; stain-blocker first if needed
Trim and doors Sand, prime bare spots, one or two enamel coats

Colour changes

Light colours over dark do not hide well, and strong reds and yellows can take extra coats on their own. Going from dark to light often needs a primer-undercoat or a third coat. Published Auckland figures put an extra topcoat for a colour change at about $500 to $1,200 on an exterior. A tinted undercoat close to the new colour helps.

White exterior colours and dark exterior colours cover the two extremes.

Diagram comparing one thin coat of paint with two coats forming an even film over timber
One coat runs thin at edges. The second closes the film.

Time between coats

Each paint’s data sheet gives a recoat time, which stretches in cool or humid weather. Recoating too soon can trap moisture, soften the film and cause wrinkling. Too long, and some enamels need a light sand to give the next coat grip. In Auckland’s humid shoulder seasons, exterior coats are often a day apart.

Weather for exterior painting explains why.

Spreading the paint properly

Each paint has a spread rate in its data sheet: roughly how many square metres a litre should cover at the right film thickness. Stretching paint further than that, by over-rolling or thinning, gives a thinner coat. A painter who uses noticeably less paint than the area calls for is leaving film out.

If you are curious, ask how many litres the quote allows for. It should broadly match the wall area divided by the spread rate, times the number of coats.

Edges, ends and the bottom board

The bottom edge of each weatherboard, board ends and sill corners are where paint fails first, because the film is thinnest and water sits there. Painters brush these first and make sure both coats reach them. On a repaint, that is also where cracking shows first.

Peeling, blistering and chalking shows what happens when edges are missed.

Coats in your quote

A written quote should state the number of coats for each surface, the primer or sealer, and the paint product. That is how you compare quotes fairly, because a lower price often means fewer coats. Ask what happens if more coats are needed for coverage.

Reading a painting quote covers the rest.

Asked before a repaint

Is one coat of paint enough?
Rarely. One coat runs thin over edges and corners, shows the old colour through, and wears through sooner. BRANZ advises two topcoats on weatherboards, and most interior systems also call for two finish coats. One coat may be enough for a quick touch-up in the same colour over sound paint.
How many coats for a dark to light colour change?
Often three, or a primer-undercoat plus two finish coats. Light colours over dark ones do not cover as well. Published Auckland figures put the cost of an extra topcoat for a big colour change at roughly $500 to $1,200 on an exterior.
How many coats does new timber need?
A full primer coat, then two finish coats, as a minimum for most exterior systems. Some systems add an undercoat. Pre-primed boards still need cut ends and nail holes primed, then two topcoats.
How long between coats of paint?
The paint maker’s data sheet gives the recoat time, which varies with temperature and humidity. Waterborne acrylics can often be recoated the same day in warm, dry weather and take longer in cool, humid conditions. Recoating too soon can trap moisture and soften the film.

Sources

When the reading is done and the brushes need picking up, Eggshell & Co is where a quote starts.

Ask us for a painting quote

Tell us about the house and the job. We reply with questions, or a day to walk around it with you.

Start a quoteCall 09 870 5756