Skip to content
Eggshell & Co Painting 09 870 5756

Painting a Lockwood or solid-timber home

A Lockwood or similar solid-timber house is the timber, inside and out: its walls are solid radiata pine boards, with no separate lining. Many were finished with clear coatings rather than paint. Painting one means preparing that clear finish so paint can grip, and working with the joints between boards. See interior painting for the general process.

Small paint tin and a brush handle on concrete beside a bright blue pool
A tin of paint ready to open. Each product has its own spread rate and recoat time on its data sheet. Photo: Shixart1985, CC BY 2.0

How these houses are built

Lockwood describes its homes as solid radiata pine walls whose boards lock together with aluminium X-shaped profiles rather than nails, needing no internal lining, and braced against wind and earthquakes with tie rods. The company was set up in Rotorua in the early 1950s, close to the pine plantations and mills.

For a painter, that means the wall face inside is the same timber as the structure. There is no plasterboard to repair or replace, so the timber surface is prepared and coated directly.

Clear finish or paint?

Many solid-timber interiors were left natural under a clear coating, and some owners want to keep that look and simply refresh it. Others paint to lighten dark rooms. Both are possible, but painting is hard to undo, because paint gets into the grain and the board joints.

Preparing old clear finishes

Paint does not grip glossy varnish or polyurethane well. The surface is cleaned to remove grease and grime, sanded to a dull, even finish, vacuumed and wiped, then primed with a product made to bond to old clear coatings. Knots and resinous areas may need a sealer so they do not bleed through.

  1. Clean with a suitable cleaner and rinse.
  2. Sand to dull the gloss; do not cut through to bare wood unevenly.
  3. Dust off with a vacuum and a damp cloth.
  4. Prime with a bonding primer; seal knots.
  5. Two finish coats of interior paint.
Six-step diagram of the order a room is painted in, from clearing to touch-ups
Top to bottom: ceiling, walls, then trim and doors.

The board joints

Solid-timber walls show horizontal joints between boards, and the timber moves slightly with the seasons. Paint is brushed into the joints so they are coated evenly, rather than filled, because filler in a moving joint cracks. The result keeps the board pattern under the paint, which most owners like.

If you want a flat, smooth wall, that is a lining job for a builder, not a paint finish.

Exterior timber on solid-timber homes

Outside, solid-timber homes are treated like other timber cladding: washed, sanded, spot-primed where bare, and given two topcoats, or re-stained if they carry a stain. The existing finish decides the system, because paint and stain need different prep. BRANZ notes that clear finishes and stains outside may need recoating every two to three years.

Primers and undercoats covers the bare-timber side.

Choosing colours for timber interiors

Timber interiors are warm, so painted walls often look best in warm whites and soft colours that sit with any remaining natural timber. A cool grey beside honey-coloured pine can look grey and flat. Test samples on the timber itself, because the old finish shows through samples differently from plasterboard.

Choosing interior colours has more on testing.

Older coatings and safety

Coatings on solid-timber homes from the 1980s or earlier may include lead in some paints, and WorkSafe advises presuming it in buildings of that age. Sanding is done with dust control, and old paint is prepared wet. Clear coatings themselves were not usually lead paints, but any painted joinery or trim may be.

Testing for lead paint covers how to check.

Asked before a repaint

Can you paint the inside of a Lockwood house?
Yes. Many owners paint some or all of the interior timber to lighten the rooms. The existing clear finish is cleaned and sanded to give grip, a primer suited to the old finish goes on, then two coats of interior paint. Some owners paint walls and keep timber ceilings or trim natural.
How do you prepare varnished timber for paint?
Clean off grease and grime, sand to dull the gloss so the new coat can grip, remove the dust, then use a primer that bonds to the old clear coating. Paint applied straight over glossy varnish tends to scratch and peel.
Will painting a Lockwood affect its value?
It depends on the buyer. Some value the natural timber look; others see a painted interior as lighter and more modern. Painting is hard to reverse, because stripping paint out of timber grain is slow, so many owners paint some rooms and keep others natural.
How are Lockwood homes built?
Lockwood describes its homes as solid radiata pine walls locked together with aluminium X-profiles rather than nailed, with no separate internal lining, braced by tie rods. The company was set up in Rotorua in the early 1950s near the pine plantations.

Sources

When the reading is done and the brushes need picking up, house painters Auckland is where a quote starts.

Ask us for a painting quote

Tell us about the house and the job. We reply with questions, or a day to walk around it with you.

Start a quoteCall 09 870 5756